How to Use a Feather Board with Woodworking Tools

Why Use the Feather board?

A Feather Board is a safety device used when working with stationary routers or power saws such as table saws or bandsaws. The purpose of a Feather Board is to apply pressure against a workpiece, keeping it flat against a machine table or fence.

If you have recently purchased a router table, have seen a table or have some other static power equipment, then you may have noticed that your new valuable occupation is already available in every related (and often, very desirable) pieces of equipment Did not come with the cans.

Do not feel cheated. From the conference, electrical tools come with the tools necessary to safely carry out their basic tasks under normal operating conditions – and this is about it.


How to Use a Featherboard With Woodworking Tools

After all, most power tool owners realize that there are some items in the “Power Tool Accessories” section that rarely come standard, without it is hard to do.

Fortunately, the power tool add-on that most woodwork “mandatory” does not seem to have a hand and feet. Some are very cheap to be prepared for the best or can be made without much trouble in the shop. The humble “Feather Board” is a prime example.

If you do not have the opportunity to use one, then the Feather Board is the most common member of the family of mechanical hold-down devices that are designed to help hold the stock against a device’s surface or fence,

while it is otherwise The machine is cut. In its simplest form, a Feather Board is a device made of a shop that is cut with a straight smear, 3 “-6” wide scrap piece.


How to Use a Featherboard With Woodworking Tools

To make one, you just cross the board at approximately 30 degrees and then make a series of about 1/8 “different cuts in the direction of the grain. The final result is a series of flexible” fingers “that are flexible at the end Board should have

A wing board actually serves two purposes. As stated, it helps to hold tight against the device or the surface of the fence while running the device.

In most cases, a Feather Board stock is able to track the stock better than the human operator. There is only one job on a wing board – to apply and even constant pressure.


Easy Lock Feather Board

There is no need to worry about things like moving the stock forward, or changing the position of the hand to maintain the appropriate feed rate.

Along with this, the wings can be positioned closer to the human finger than the action, applying pressure where it is most effective and can be overcome by the least vibration.

Together, these favorable circumstances make basically crucial for the activity of a quilling board or other mechanical hold-down gadget to make a fragile edge, bent, and rabbit task.


Using a wing board also provides security benefits. On account of the introduction of the edge of your finger, when a quill barricade is set to apply a delicate weight, it will permit simple development toward the cut, while all the development the other way will stop.

And it should be noted that they are not the replacement knife and anti-kickback claw replacement, which now come standard with most table saws, the Feather Board provides significant kickback insurance.

Can you make your own wing board, or prepare them? Creating your own is a viable option: the wing board made of a shop can just work and models purchased from a store, and of course they are almost cost-free.


The Feather Board Made from a Basic Store

But like most things, there are some tradeoffs: making the Feather Board is not particularly difficult, but they do not make themselves.

How much you enjoy doing jing about yourself, and how many store-time you have, you can decide that the chance to come up with your work is more than the modest cost of the store-bought model.

At this point, the store wings are much less user-friendly than the generally prepared varieties. If you are planning to clamp the Feather Board made from a basic store, then remember that you need to do this,

while you keep it in a position that puts a lot of pressure on the representative piece of stock. He could, in itself, include clutches with a surprisingly weird one hand.

Getting a secure wing board in the right place can be particularly difficult when clamping on the surface of the target device; Bedding and router table top were seen in the most table so that the process was not designed to be easy and convenient.


feather board design

On the other hand, the rocker table Feather Board takes steps in favor of clamping problem. Their mater slot hold-down bar firmer broadly extends to clamp into a standard 3/4 ‘xx / 8’ miter slot and secures its position simultaneously with a turn of two knobs.

The Rockefeller quill board likewise makes the more included set-up less demanding. A wing load up isn’t in every case enough; Sometimes, you require “stacked” wings.

When you are running vertical stock with a fence – in the case of cutting vertical panels with vertical panel-lifting bits – you need the additional support of a second feed board near the top of the fence.

The second wing board ensures that the full face of the stock will be in contact with the fence, not only downwards An ideal companion for our popular Deluxe Router Router Fence,

the Rockler Double Feather Board Kit allows you to place two completely aligned wings at the same instant on top of each other

Leave a Reply

Your email address will not be published. Required fields are marked *